Book My Estimate

 

 

We have stumbled on the article pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the internet and believe it made sense to share it with you in this article.

Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably tough job. If the old tub is conveniently available, the project can relocate rapidly; if you have to open up a wall to get rid of the old tub and place the new bath tub, the task is much harder. In either instance, the project is within a residence handyman's skills, although you will certainly require a helper to vacate the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the job and also are comfortable attempting it. Rather than employing a service provider to take control of a halfway-completed project, it is much better to consider utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This short article will certainly help you set up a new tub in your bathroom if you have currently bought a brand-new tub as well as do not need to transform the arrangement of your previous water system pipes.
Your tools and also material list need to comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Getting ready for the Installment

To start with, the supporting frame supplied with the bathroom needs to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps system to avoid stress on the bath tub.
Fit the versatile faucet adapters to the bottom of both taps utilizing 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its final position.

 

 

Removing Old Taps

If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The process of removing the existing faucets can be fairly troublesome due to the restricted access that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the staying water that will originate from the pipelines. Once the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.

 

 

Installing the Tub

Using both wooden boards under its feet, position the tub in the called for position. The wood boards are valuable in uniformly spreading the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the bathtub till the spirit level checks out level.
To set up taps, fit all-time low of the outermost versatile faucet port to the appropriate supply pipeline by making a compression join; then do the exact same for the other faucet.
Switch on the water as well as check all joints as well as new pipework for leakages and tighten them if needed. Load the tub as well as also inspect the overflow electrical outlet and the regular outlet for leaks.
Ultimately, fix the bathroom paneling as described in the maker's user's manual. Tiling as well as securing around the bath tub ought to wait till the bathtub has been utilized at the very least once as this will certainly resolve it into its final placement.

 

 

Suitable New Taps

If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin guaranteeing that the washing machines remain in area between the tap as well as the sink. Protect the faucet in position with the manufacturer provided backnut. When the tap is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical faucet ports. The previous kind needs to be attached to the tap ends first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.

 

 

Tiling Around the Tub

In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture an inflexible seal, creating the water to permeate the wall surface between the bath as well as the tiling, resulting in problems with moisture as well as possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your components and also installations. They are offered in tubes as well as cartridges, as well as are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to permit the activity experienced when the bathtub is in use. The sealant can fracture rather very early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally quickly offered on the market. It is recommended to fit the floor tiles utilizing waterproof or water resistant adhesive and cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you enjoyed our piece on How to Install a Bathtub Yourself. Many thanks for taking time to read our article post. Enjoyed reading our write up? Please share it. Let somebody else find it. Thank you so much for your time spent reading it.

This Post